Skip to content
How to Raise pH in Pool: Easy 2026 Guide + Soda Ash Calculator

How to Raise pH in Pool: Easy 2026 Guide + Soda Ash Calculator

⏱ 5 min read · Updated November 2026 · By the MSP Supply pool techs

Quick answerTo raise pH in a pool, add soda ash (pH Up) with the pump running, aiming for pH 7.4–7.6. If alkalinity is under 80 ppm, raise it first with baking soda, then retest pH.

Low pH eats at plaster, corrodes heaters and ladders, and stings eyes. In 2026 the fix is still cheap and fast.

Here's how much to add, which product to use, and how to keep pH from crashing again.

What pH Should a Pool Be?

Keep pH at 7.4–7.6. Below 7.2, water turns corrosive. Raise it the same day.

Pool pH scale6.87.07.27.47.67.88.0Low: corrosiveIdeal 7.4–7.6Too highadd soda ashSoda ash moves pH right, toward the green zone
pH reading What it means Action
Below 7.0 Very low: etches plaster, corrodes metal, eats vinyl Check TA, then soda ash. Retest, repeat
7.0–7.3 Low Soda ash dose (or aerate)
7.4–7.6 Ideal Nothing
7.8+ Too high See how to lower pH

Soda Ash & Baking Soda Calculator

How much pH Up do I need?

Enter your test results. Soda ash (sodium carbonate) raises pH. Baking soda (sodium bicarbonate) raises alkalinity.

Soda ash / pH Up–
Baking soda / Alkalinity Up–

Don't know your gallons? Rectangle: length × width × average depth × 7.5. Estimates only; pools vary. Add about 3/4 of the soda ash dose, retest after 4–6 hours, then finish.

Soda Ash vs Baking Soda in 2026: Which One Raises pH?

Both are bases, but they do different jobs. Test pH and alkalinity before you pick.

Soda ash Baking soda
Chemical Sodium carbonate Sodium bicarbonate
Main effect Raises pH Raises total alkalinity
Effect on pH Strong Small
Typical dose Ounces (see calculator) 1.4 lb per 10,000 gal = +10 ppm TA
Best for Low pH, TA in range Low TA, pH that keeps bouncing

Does baking soda raise pH? A little. It mostly raises alkalinity. If pH is low and TA is fine, use soda ash.

How to Raise pH in a Pool: Step-by-Step

  1. Test pH, alkalinity and CYA. A drop kit gives the most accurate numbers. See how to test pool water.
  2. Fix TA first if it's under 80 ppm. Add baking soda, circulate 6 hours, retest pH.
  3. Get your soda ash dose from the calculator. Measure about 3/4 of it.
  4. Pre-dissolve in a bucket of pool water. Add the product to the water, not water to the product.
  5. Pour slowly in front of a return jet with the pump running. Keep swimmers out.
  6. Circulate. Wait at least 30 minutes before swimming.
  7. Retest after 4–6 hours. Add the rest only if pH is still below 7.4.
Pro tip: Too much soda ash at once can turn water cloudy, especially with high calcium. Split big doses into two. Wear gloves and goggles, never mix soda ash with acid or chlorine in the same bucket, and never stand in the pool while adding chemicals.

pH reading low? Fix it today.

Shop Pool Chemicals →

pH Up Dose Chart

Soda ash estimates at TA 90 ppm and CYA 40 ppm. Higher alkalinity needs more.

Pool size pH 7.2 → 7.5 pH 7.0 → 7.5 pH 6.8 → 7.5
10,000 gal 14 oz 28 oz (1.7 lb) 47 oz (3.0 lb)
15,000 gal 20 oz (1.3 lb) 41 oz (2.6 lb) 71 oz (4.4 lb)
20,000 gal 27 oz (1.7 lb) 55 oz (3.5 lb) 95 oz (5.9 lb)
25,000 gal 34 oz (2.1 lb) 69 oz (4.3 lb) 118 oz (7.4 lb)

oz = soda ash by weight. 16 oz = 1 lb. A 5 lb pouch holds 80 oz.

Raise pH Without Chemicals: Aeration

Aeration pushes CO₂ out of the water, so pH rises without raising alkalinity. It's the best fix when pH is low but TA is high.

  • Point return jets up so they break the surface.
  • Run waterfalls, spillways or bubblers for several hours.
  • Retest every few hours. It's slower than soda ash, but free.

Why Pool pH Keeps Dropping

  • Trichlor tablets are acidic and pull pH down steadily.
  • Rain is naturally acidic and dilutes alkalinity.
  • Low alkalinity lets pH swing. Keep TA at 80–120 ppm.
  • Too much acid after a pH-down dose. Always add 3/4 and retest.
  • Dichlor shock is slightly acidic too.

Shocking after you balance? Check how much chlorine to add.

📋 Raise pH Checklist

How to raise pH in a pool · msppool.com

  • Before
  • Test pH, TA and CYA
  • Know your pool gallons
  • TA under 80? Baking soda first
  • Calculate the soda ash dose
  • Adding pH Up
  • Gloves + goggles on
  • Pump running, swimmers out
  • Pre-dissolve in pool water
  • Pour 3/4 dose at a return jet
  • After
  • Wait 30+ min to swim
  • Retest after 4–6 hours
  • Target pH 7.4–7.6
  • Target TA 80–120 ppm
🖨 Print Checklist

Get your pH back in range

  • ✔ pH Up, Alkalinity Up & test kits in stock
  • ✔ Shipped nationwide from Florida
  • ✔ Real pool pros: (305) 359-7665
Shop ChemicalsCall Us
Cart 0

Your cart is currently empty.

Start Shopping